-
1 constant-frequency supply
источник постоянной частоты
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > constant-frequency supply
-
2 constant-frequency supply
thre-phase supply — трехфазное питание; источник трехфазного питания
two-phase supply — двухфазное электропитание; источник двухфазного питания
English-Russian dictionary of Information technology > constant-frequency supply
-
3 constant-frequency supply
Телекоммуникации: источник постоянной частотыУниверсальный англо-русский словарь > constant-frequency supply
-
4 constant-frequency supply
English-Russian dictionary of modern telecommunications > constant-frequency supply
-
5 constant-frequency supply
English-Russian dictionary of microelectronics > constant-frequency supply
-
6 constant-frequency supply
Englsh-Russian aviation and space dictionary > constant-frequency supply
-
7 precisely regulated ac power supply with constant frequency
- питание переменным током с точно регулируемым (+2%) напряжением и постоянной частотой
питание переменным током с точно регулируемым (+2%) напряжением и постоянной частотой
(класс 1, тип А, группа 111 по МЭК)
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > precisely regulated ac power supply with constant frequency
-
8 precisely regulated ac power supply with constant frequency
Электротехника: питание переменным током с точно регулируемым (+2%) напряжением и постоянной частотой (класс 1, тип А, группа III no МЭК)Универсальный англо-русский словарь > precisely regulated ac power supply with constant frequency
-
9 supply
-
10 frequency
= freq1) частота (1. величина, обратная периоду; величина, пропорциональная обратному периоду (напр. круговая частота) 2. частота появления случайного события, отношение встречаемости к числу испытаний) || частотный2) встречаемость ( случайного события); периодичность•- acoustic frequency
- acoustical frequency
- actual frequency
- air-ground radio frequency
- air-to-ground radio frequency
- alias frequency
- alpha cutoff frequency
- alternate frequency
- angular frequency
- antenna resonant frequency
- antiferromagnetic resonance frequency
- antiresonant frequency
- anti-Stokes frequency
- assigned frequency
- atomic frequency
- audio frequency
- aural center frequency
- authorized frequency
- avalanche frequency
- base frequency
- base-transport cutoff frequency
- basic frequency
- bass frequency
- beat frequency
- beta cutoff frequency
- bias frequency
- Bragg frequency
- break frequency
- bubble-propagation frequency
- bus frequency
- carrier frequency
- center frequency
- channel frequency
- characteristic frequency
- chopping frequency
- circular frequency
- clock frequency
- co-channel sound frequency
- collision frequency
- combination frequency
- commercial frequency
- complex frequency
- constant frequency
- core frequency
- corner frequency
- critical frequency
- critical fusion frequency
- crossover frequency
- cumulative relative frequency
- cutoff frequency
- cyclotron frequency
- data frequency
- data communications frequency
- 3-dB frequency
- dedicated frequency
- difference frequency
- diffusion frequency
- distress frequency
- Doppler frequency
- Doppler-beat frequency
- Doppler-shifted frequency
- down-link frequency
- drift frequency
- driving frequency
- dynamic-scattering cutoff frequency
- echo frequency
- electron Langmuir frequency
- electron paramagnetic resonance frequency
- electron plasma frequency
- expected frequency
- extinction frequency
- extremely high frequency
- extremely low frequency
- facsimile picture frequency
- ferrimagnetic-resonance frequency
- ferromagnetic-resonance frequency
- field frequency
- fixed frequency
- flicker-fusion frequency
- flutter frequency
- folding frequency
- forward-bias cutoff frequency
- frame frequency
- free-running frequency
- fundamental frequency
- fundamental scanning frequency
- fusion frequency
- gap frequency
- gliding frequency
- ground-air frequency
- ground-to-air frequency
- group frequency
- Gunn frequency
- half-power frequency
- harmonic frequency
- helicon frequency
- heterodyne frequency
- high frequency
- highest probable frequency
- horizontal-line frequency
- horizontal-scanning frequency
- hyperfine frequency
- hyperfine transition frequency
- hyperhigh frequency
- idler frequency
- image frequency
- imaginery frequency
- IMPATT-frequency
- impingement frequency
- impulse frequency - instantaneous frequency
- intercarrier frequency
- intermediate frequency
- intermodulation frequency
- intermodulation component frequency
- inversion-layer cutoff frequency
- ion cyclotron frequency
- ionization frequency
- ion plasma frequency
- jittered pulse-recurrence frequency
- Josephson frequency
- keying frequency
- knee frequency
- Langmuir plasma frequency
- Larmor frequency
- laser-frequency
- laser-emission-frequency
- lattice vibration frequency
- line frequency
- line screen frequency
- lobe frequency
- local-oscillator frequency
- locking frequency
- low frequency
- lower side frequency - lowest useful high frequency
- magnetohydrodynamic frequency
- magnetoplasma frequency
- mains frequency
- maser frequency
- maser-emission frequency
- master frequency
- maximum frequency of oscillation
- maximum keying frequency
- maximum modulating frequency - microwave frequency
- midband frequency
- mode frequency
- modulation frequency
- multiple frequency
- natural frequency
- nominal frequency
- notch frequency
- note frequency
- Nyquist frequency
- observed frequency
- operating frequency
- optical frequency - photoelectric threshold frequency
- picture frequency
- piezoelectric crystal antiresonant frequency
- piezoelectric crystal resonant frequency
- pilot frequency
- plasma frequency
- power frequency
- power-line frequency
- precession frequency
- primary frequency
- pulse-recurrence frequency - pumping frequency
- quasi-optical frequency
- quench frequency
- quenching frequency
- quiescent frequency
- radian frequency
- radio frequency
- rated frequency
- reactive cutoff frequency
- real frequency
- reference frequency
- relative frequency
- relative frequency
- repetition frequency
- resistive cutoff frequency
- resonance frequency
- resonant frequency
- rest frequency
- resting frequency
- ringing frequency
- ripple frequency
- scan frequency
- scanning-line frequency
- screen frequency
- secondary frequency
- second-channel frequency
- self-neutralization frequency
- self-resonant frequency
- SH frequency
- side frequency
- sonic frequency
- sound frequency
- sound carrier frequency
- sound center frequency
- space frequency
- spark frequency
- spatial frequency
- speech frequency
- spike frequency
- spin frequency
- spot frequency
- standard frequency
- Stokes frequency
- subaudio frequency
- subcarrier frequency
- subharmonic frequency
- sub-Nyquist frequency
- subsonic frequency
- sub-telephone frequency
- sum frequency
- summation frequency
- superaudio frequency - super-telephone frequency
- supply frequency
- suppression frequency
- sweep frequency
- synchronizing frequency
- threshold frequency - toggle frequency
- tone frequency
- top baseband frequency
- transition frequency
- transit-time frequency
- transit-time cutoff frequency
- transmission frequency
- TRAPATT frequency
- trapped plasma frequency
- treble frequency
- turnover frequency
- ultra-audible frequency - undamped frequency
- uniform precession frequency
- unity-gain frequency
- up-link frequency
- upper side frequency
- variable frequency
- vertical frequency - video frequency
- vision frequency
- vision carrier frequency
- visual carrier frequency
- voice frequency
- voltage gain cutoff frequency
- waveguide cutoff frequency
- window frequency
- wow frequency -
11 frequency
1) частота (1. величина, обратная периоду; величина, пропорциональная обратному периоду (напр. круговая частота) 2. частота появления случайного события, отношение встречаемости к числу испытаний) || частотный2) встречаемость ( случайного события); периодичность•- absolute cutoff frequency
- acoustic frequency
- acoustical frequency
- actual frequency
- air-ground radio frequency
- air-to-ground radio frequency
- alias frequency
- alpha cutoff frequency
- alternate frequency
- angular frequency
- antenna resonant frequency
- antiferromagnetic resonance frequency
- antiresonant frequency
- anti-Stokes frequency
- assigned frequency
- atomic frequency
- audio frequency
- aural center frequency
- authorized frequency
- avalanche frequency
- base frequency
- base-transport cutoff frequency
- basic frequency
- bass frequency
- beat frequency
- beta cutoff frequency
- bias frequency
- Bragg frequency
- break frequency
- bubble-propagation frequency
- bus frequency
- carrier frequency
- center frequency
- channel frequency
- characteristic frequency
- chopping frequency
- circular frequency
- clock frequency
- co-channel sound frequency
- collision frequency
- combination frequency
- commercial frequency
- complex frequency
- constant frequency
- core frequency
- corner frequency
- critical frequency
- critical fusion frequency
- crossover frequency
- cumulative relative frequency
- cutoff frequency
- cyclotron frequency
- data communications frequency
- data frequency
- dedicated frequency
- difference frequency
- diffusion frequency
- distress frequency
- Doppler frequency
- Doppler-beat frequency
- Doppler-shifted frequency
- down-link frequency
- drift frequency
- driving frequency
- dynamic-scattering cutoff frequency
- echo frequency
- electron Langmuir frequency
- electron paramagnetic resonance frequency
- electron plasma frequency
- expected frequency
- extinction frequency
- extremely high frequency
- extremely low frequency
- facsimile picture frequency
- ferrimagnetic-resonance frequency
- ferromagnetic-resonance frequency
- field frequency
- fixed frequency
- flicker-fusion frequency
- flutter frequency
- folding frequency
- forward-bias cutoff frequency
- frame frequency
- free-running frequency
- fundamental frequency
- fundamental scanning frequency
- fusion frequency
- gap frequency
- gliding frequency
- ground-air frequency
- ground-to-air frequency
- group frequency
- Gunn frequency
- half-power frequency
- harmonic frequency
- helicon frequency
- heterodyne frequency
- high frequency
- highest probable frequency
- horizontal-line frequency
- horizontal-scanning frequency
- hyperfine frequency
- hyperfine transition frequency
- hyperhigh frequency
- idler frequency
- image frequency
- imaginery frequency
- IMPATT-frequency
- impingement frequency
- impulse frequency
- infralow frequency
- infrasonic frequency
- instantaneous frequency
- intercarrier frequency
- intermediate frequency
- intermodulation component frequency
- intermodulation frequency
- inversion-layer cutoff frequency
- ion cyclotron frequency
- ion plasma frequency
- ionization frequency
- jittered pulse-recurrence frequency
- Josephson frequency
- keying frequency
- knee frequency
- Langmuir plasma frequency
- Larmor frequency
- laser-emission-frequency
- laser-frequency
- lattice vibration frequency
- line frequency
- line screen frequency
- lobe frequency
- local-oscillator frequency
- locking frequency
- low frequency
- lower side frequency
- lowest observed frequency
- lowest useful frequency
- lowest useful high frequency
- magnetohydrodynamic frequency
- magnetoplasma frequency
- mains frequency
- maser frequency
- maser-emission frequency
- master frequency
- maximum frequency of oscillation
- maximum keying frequency
- maximum modulating frequency
- maximum observed frequency
- maximum usable frequency
- medium frequency
- microwave frequency
- midband frequency
- mode frequency
- modulation frequency
- multiple frequency
- natural frequency
- nominal frequency
- notch frequency
- note frequency
- Nyquist frequency
- observed frequency
- operating frequency
- optical frequency
- optimum working frequency
- penetration frequency
- photoelectric threshold frequency
- picture frequency
- piezoelectric crystal antiresonant frequency
- piezoelectric crystal resonant frequency
- pilot frequency
- plasma frequency
- power frequency
- power-line frequency
- precession frequency
- primary frequency
- pulse-recurrence frequency
- pulse-repetition frequency
- pump frequency
- pumping frequency
- quasi-optical frequency
- quench frequency
- quenching frequency
- quiescent frequency
- radian frequency
- radio frequency
- rated frequency
- reactive cutoff frequency
- real frequency
- reference frequency
- relative frequency
- repetition frequency
- resistive cutoff frequency
- resonance frequency
- resonant frequency
- rest frequency
- resting frequency
- ringing frequency
- ripple frequency
- scan frequency
- scanning-line frequency
- screen frequency
- secondary frequency
- second-channel frequency
- self-neutralization frequency
- self-resonant frequency
- SH frequency
- side frequency
- sonic frequency
- sound carrier frequency
- sound center frequency
- sound frequency
- space frequency
- spark frequency
- spatial frequency
- speech frequency
- spike frequency
- spin frequency
- spot frequency
- standard frequency
- Stokes frequency
- subaudio frequency
- subcarrier frequency
- subharmonic frequency
- sub-Nyquist frequency
- subsonic frequency
- sub-telephone frequency
- sum frequency
- summation frequency
- superaudio frequency
- superhigh frequency
- supersonic frequency
- super-telephone frequency
- supply frequency
- suppression frequency
- sweep frequency
- synchronizing frequency
- threshold frequency
- timed radio frequency
- timing frequency
- toggle frequency
- tone frequency
- top baseband frequency
- transition frequency
- transit-time cutoff frequency
- transit-time frequency
- transmission frequency
- TRAPATT frequency
- trapped plasma frequency
- treble frequency
- turnover frequency
- ultra-audible frequency
- ultrahigh frequency
- ultrasonic frequency
- unassigned frequency
- undamped frequency
- uniform precession frequency
- unity-gain frequency
- up-link frequency
- upper side frequency
- variable frequency
- vertical frequency
- very high frequency
- very low frequency
- video frequency
- vision carrier frequency
- vision frequency
- visual carrier frequency
- voice frequency
- voltage gain cutoff frequency
- waveguide cutoff frequency
- window frequency
- wow frequencyThe New English-Russian Dictionary of Radio-electronics > frequency
-
12 external power supply
1. внешний источник питания2. внешний источник энергииelectrical supply — источник тока; подача электроэнергии
English-Russian big polytechnic dictionary > external power supply
-
13 DOL
- эффект операционного рычага
- пускатель прямого действия
- прямой пуск вращающегося электродвигателя
- Министерство труда (США)
- концентрация растворённого кислорода
концентрация растворённого кислорода
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
Министерство труда (США)
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
пускатель прямого действия
Пускатель, одноступенчато подающий сетевое напряжение на выводы двигателя.
(МЭС 441-14-40)
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
Пускатели переменного тока для прямого непосредственного пуска (с полным напряжением)
Пускатели, предназначенные для пуска двигателя, разгона его до номинальной скорости, защиты двигателя и подключенных к нему цепей от рабочих перегрузок и отключения питания двигателя.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
direct-on-line starter
a starter which connects the line voltage across the motor terminals in one step
[IEV number 441-14-40]FR
démarreur direct
démarreur qui applique la tension d'alimentation sur les bornes du moteur en une seule manoeuvre
[IEV number 441-14-40]Параллельные тексты EN-RU
Direct-on-line starters
Starters which connect the line voltage across the motor terminals in one step, intended to start and accelerate a motor to normal speed.
They shall ensure switching and protection functions as prescribed in the general definition.
[ABB]Пускатели прямого действия
Пускатели, одноступенчато подающие сетевое напряжение на зажимы двигателя и предназначенные для его пуска и разгона до номинальной скорости.
Кроме того, они должны обеспечивать коммутацию и защиту в соответствии с общим определением.
[Перевод Интент]Тематики
EN
DE
FR
эффект операционного рычага
эффект производственного рычага
Эффект операционного рычага - выражение того факта, что любое изменение выручки от реализации порождает изменение прибыли. Сила воздействия операционного рычага вычисляется как частное от деления выручки от реализации после возмещения переменных затрат на прибыль.
[ http://www.lexikon.ru/dict/fin/a.html]Тематики
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > DOL
-
14 direct starting
прямой пуск
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct starting
-
15 across-the-line starting (US)
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > across-the-line starting (US)
-
16 direct line starting
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct line starting
-
17 direct operation of a motor
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct operation of a motor
-
18 direct-on-line starting
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > direct-on-line starting
-
19 full voltage starter application
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Англо-русский словарь нормативно-технической терминологии > full voltage starter application
-
20 circuit
1) схема; цепь; контур2) линия3) канал4) сеть•- adapter circuit
- adjustment circuit
- alive circuit
- announcing circuit
- anode circuit
- antisidetone circuit
- asynchronous circuit
- automatic reset-data circuit
- automatic ringdown circuit
- automatic start circuit
- auxiliary circuit
- balanced circuit
- balanced-wire circuit
- balancing circuit
- band-switching circuit
- basic circuit
- black-level restoring circuit
- black-level stretch circuit
- bootstrap circuit
- branch circuit
- branched circuit
- bridge antisidetone circuit
- building-out circuit
- built-up circuit
- Buttler circuit
- bypass circuit
- cached circuit
- call circuit
- capacitor-coupled circuit
- capacitor-switched circuit
- capacitor-switching circuit
- central-battery circuit
- chain-type connection circuit
- character generator large-scale integration circuit
- charge-coupled device circuit
- check parity circuit
- checkout circuit
- chrominance matrix circuit
- chrominance separation circuit
- chrominance takeoff circuit
- clamp-on circuit
- closed circuit
- coarse phasing circuit
- coaxial circuit
- coincidence circuit
- color-balance circuit
- color-indexing circuit
- color-purity circuit
- combinational-circuit circuit
- combined-supply circuit
- common-base circuit
- common-battery circuit
- common-collector circuit
- common-drain circuit
- common-emitter circuit
- common-gate circuit
- common-source circuit
- common-user circuit
- communication circuit
- comparing circuit
- compensating antisidetone circuit
- complemental metal-oxide-semiconductor circuit
- composite circuit
- conductor-bundled static wire circuit
- conference circuit
- connecting circuit
- constant-closed circuit
- contactor-relay circuit
- continental circuit
- convergence circuit
- cord circuit
- correcting circuit
- Costas circuit
- counter-coupling circuit
- counting-down circuit
- coupled circuit
- cross-bus matrix circuit
- crossed-waveguide circuit
- cue circuit
- cutoff circuit
- Darlingtone circuit
- data circuit
- data-transmission circuit
- dc restoration circuit
- decoder circuit
- delay circuit
- demodulation circuit
- dial-up circuit
- diamond circuit
- differencing circuit
- differential-frequency circuit
- digital circuit
- digital-excitation circuit
- digital-leased circuit
- diode-clamping circuit
- diode-clipping circuit
- diode-stabilitron circuit
- direct international circuit
- direct-connection circuit
- direct-transit international circuit
- direct-wire circuit
- double half-wave circuit
- double-ended cord circuit
- double-loop circuit
- dual circuit
- earth circuit
- earthed circuit
- echo-absorption circuit
- edge derivation circuit
- electric circuit
- electronic circuit
- elementary circuit
- encoding circuit
- energized circuit
- engineering circuit
- equivalent circuit
- error-subtracting circuit
- external circuit
- fallback circuit
- feed circuit
- feedback circuit
- fiber-optic circuit
- fire-control circuit
- fixed-virtual circuit
- flexible circuit
- flexible-stage circuit
- flywheel circuit
- forked circuit
- four-wire circuit
- frame scanning circuit
- frequency-changing circuit
- frequency-protection circuit
- full-accessible circuit
- full-period allocated circuit
- functional-switching circuit
- gallium-arsenide integrated circuit
- gating circuit
- generating circuit
- Gilbert circuit
- Grets circuit
- grid circuit
- ground-return circuit
- grouping circuit
- half-bridge circuit
- half-wave circuit
- hardened circuit
- head circuit
- HF-correction circuit
- holding circuit
- horizontal deflection circuit
- hybrid circuit
- hypothetical reference circuit
- idle lighting limiting circuit
- inclined adjustment circuit
- incoming circuit
- independent circuit
- inductive circuit
- input circuit
- input-by-output matrix circuit
- inquiry circuit
- integrated circuit
- integrating circuit
- interchange circuit
- interface-integrated circuit
- interferenced circuit
- interferencing circuit
- international leased circuit
- interstage coupling circuit
- invertor circuit
- ISDN echo cancellation circuit
- isochronic circuit
- Jiakoletto circuit
- junction circuit
- Karp circuit
- keep-alive circuit
- key section power circuit
- killer circuit
- ladder circuit
- lamp circuit
- large-scale integration circuit
- latched circuit
- LCR circuit
- lead changeover circuit
- LF-correction circuit
- line circuit
- linear circuit
- link circuit
- live circuit
- local circuit
- lock-in circuit
- locking circuit
- lock-out circuit
- long circuit
- long-distance circuit
- longitudinal circuit
- loop circuit
- lossless resonant circuit
- L-shaped circuit
- magnetic convergence circuit
- main supply circuit
- make circuit
- Marx circuit
- match circuit
- matching circuit
- matrix circuit
- message circuit
- microelectronic circuit
- microphone supply circuit
- multidrop circuit
- multijunctor circuit
- multiloop circuit
- multipoint circuit
- muting circuit
- neodymium magnetic circuit
- neutral circuit
- neutralization circuit
- neutralizing circuit
- noise-rejecting circuit
- noise-suicide circuit
- nonlinear circuit
- NOT circuit
- on-call circuit
- open circuit
- optoelectronic integrated circuit
- OR circuit
- order wire circuits
- OR-ELSE circuit
- oscillating circuit
- oscillation circuit
- output circuit
- output voltage tracking circuit
- packaged circuit
- paging circuit
- parallel circuit
- partially accessible circuit
- peaking circuit
- periodic closed circuit
- phantom circuit
- phase comparating circuit
- phase compensating circuit
- phase-shift circuit
- phase-substitution circuit
- physical circuit
- pilot circuit
- pilot-make-busy circuit
- planar circuit
- point-to-point circuit
- polling circuit
- polyphase circuit
- power circuit
- power-supply circuit
- precision phasing circuit
- primary circuit
- printed circuit
- private leased circuit
- protection circuit
- pulse-phase control circuit
- push-to-talk circuit
- push-to-type circuit
- quenching circuit
- quiet-tuning circuit
- radial supply circuit
- radio circuit
- RC circuit
- reactance control circuit
- reading circuit
- rectification circuit
- reference circuit
- rejecting circuit
- relay cutout circuit
- remote control circuit
- remote-ring circuit
- repeat circuit
- reset circuit
- resonance circuit
- resonant circuit
- reverse circuit
- reverse diode circuit
- ring circuit
- ringing circuit
- sample-and-hold circuit
- scaling circuit
- Scott circuit
- secondary circuit
- section substitution circuit
- selecting circuit
- selective circuit
- self-locked circuit
- series circuit
- series-oscillating circuit
- series-parallel circuit
- series-peaking circuit
- series-tuned circuit
- shaping circuit
- shaved single frequency circuit
- short circuit
- shunt circuit
- shunting circuit
- shunt-peaking circuit
- side circuit
- signal circuit
- signal processing circuit
- signal recovery circuit
- single-current circuit
- single-ended push-pull circuit
- single-frequency resonance circuit
- single-phase bridge circuit
- single-phase circuit
- snap-acting circuit
- solving circuit
- sound-program circuit
- spark-safe circuit
- speech circuit
- speed regulating circuit
- squaring circuit
- stabilizer circuit
- stable circuit
- stage circuit
- stage control circuit
- standard cable circuit
- standard circuit
- standby circuit
- stenode circuit
- storage large-scale integration circuit
- storage locking circuit
- straightforward circuit
- strap magnetic circuit
- strip-line circuit
- super large scale integration circuit
- superimposed circuit
- superposed circuit
- supply circuit
- sweep circuit
- switched circuit
- switching circuit
- symistor control circuit
- synchronous circuit
- tail circuit
- talk-back circuit
- tandem data circuit
- tank circuit
- tapped magnetic circuit
- tapped stage circuit
- telecommunication circuit
- telecommunication-protection circuit
- telegraph circuit
- telegraph grade circuit
- telegraph signal generating circuit
- telephone circuit
- telephone signal generating circuit
- telesignaling receiving circuit
- telesignaling sending circuit
- television circuit
- terminal circuit
- test circuit
- testing circuit
- third circuit
- three-loop circuit
- three-phase input circuit
- three-wire circuit
- through circuit
- thyristor control circuit
- time protection circuit
- time-delay circuit
- time-interval protection circuit
- time-setting circuit
- timing circuit
- toll circuit
- touch sensing circuit
- touch tone dial circuit
- transformer substitution circuit
- transformer-coupled circuit
- transistor clipping circuit
- transistor collector circuit
- transistor control circuit
- transistor protection circuit
- tributary circuit
- triode clamp circuit
- trunk circuit
- T-shaped circuit
- tuned circuit
- twelve-pulse circuit
- two-frequency resonance circuit
- two-loop circuit
- two-wire-ground circuit
- uniform circuit
- unstable circuit
- untapped circuit
- untapped magnetic circuit
- U-shaped circuit
- variometer controlling circuit
- video circuit
- virtual circuit
- voice circuit
- voltage multiplying circuit
- voltage sensor circuit
- watching output circuit
- wideband circuit
- wire circuit
- wired circuitEnglish-Russian dictionary of telecommunications and their abbreviations > circuit
См. также в других словарях:
constant-speed drive unit — A unit that drives a generator at a constant RPM, regardless of the engine RPM, thus ensuring a constant supply frequency. It is functionally a hydraulic transmission, similar to those in use in automobiles. It may be controlled electrically or… … Aviation dictionary
Power supply — For the Budgie album, see Power Supply (album). A vacuum tube rackmount adjustable power supply, capable of +/ 1500 volts DC, 0 to 100mA output, with amperage limiting capability. A power supply is a device that supplies electrical energy … Wikipedia
Uninterruptible power supply — A small free standing UPS … Wikipedia
Switched-mode power supply — switched mode power supply. A bridge rectifier B Input filter capacitors C Transformer D output filter coil E output filter capacitors ] A switched mode power supply, switching mode power supply or SMPS, is an electronic power supply unit (PSU)… … Wikipedia
Variable-frequency drive — A variable frequency drive (VFD) is a system for controlling the rotational speed of an alternating current (AC) electric motor by controlling the frequency of the electrical power supplied to the motor.cite book | first=Sylvester J. |… … Wikipedia
Welding power supply — A welding power supply is a device that provides an electric current to perform welding. Welding usually requires high current (over 80 amperes) and it can need above 12,000 amps in spot welding. Low current can also be used; welding two razor… … Wikipedia
Power supply unit (computer) — Power supply unit with top cover removed A power supply unit (PSU) supplies direct current (DC) power to the other components in a computer. It converts general purpose alternating current (AC) electric power from the mains (110 V to… … Wikipedia
FM4 Frequency Festival — The FM4 Frequency Festival, also Frequency Festival or just Frequency, formerly Vienna City Festival, is a music festival that takes place near Salzburg, Austria, usually every August. It is promoted by one of Austria s national radio stations,… … Wikipedia
electric motor — motor (def. 4). [1885 90] * * * Introduction any of a class of devices that convert electrical energy to mechanical energy, usually by employing electromagnetic phenomena. Most electric motors develop their mechanical torque by the… … Universalium
источник постоянной частоты — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] Тематики электротехника, основные понятия EN constant frequency supply … Справочник технического переводчика
nervous system, human — ▪ anatomy Introduction system that conducts stimuli from sensory receptors to the brain and spinal cord and that conducts impulses back to other parts of the body. As with other higher vertebrates, the human nervous system has two main… … Universalium